SBE 19plus V2 SeaCAT Profiler CTD

SBE 19plus V2 SeaCAT Profiler CTD

Profiling or moored Conductivity, Temperature, Pressure, and up to seven auxiliary sensors, with 4 Hz sampling, and internal memory and batteries.

SUMMARY

  • Conductivity, Temperature, Pressure, and up to seven auxiliary sensors.
  • User-programmable mode: profiling at 4 Hz, or moored sampling at user-programmable intervals.
  • RS-232 serial interface, internal memory, and internal batteries (can be powered externally).
  • Pump-controlled, T-C ducted flow to minimize salinity spiking.
  • Depths to 600 or 7000 meters.
  • Adds to Sea-Bird's SeaCAT family, field-proven since 1987.
  • Five-year limited warranty.

DESCRIPTION

The SBE 19plus V2 (Version 2) SeaCAT Profiler measures conductivity, temperature, and pressure (depth) and provides high accuracy and resolution, reliability, and ease-of-use for a wide range of research, monitoring, and engineering applications. The pump-controlled, TC-ducted flow configuration minimizes salinity spiking caused by ship heave and allows for slow descent rates without slowing sensor responses, improving dynamic accuracy and resolving small scale structure in the water column.

Compared to the previous 19plus, the V2 incorporates an electronics upgrade and additional features, with six differentially amplified A/D input channels, one RS-232 data input channel, and 64 MB FLASH memory. An optional Digiquartz® pressure sensor provides highest-accuracy pressure measurement. Data can be output in XML as well as ASCII and HEX formats. Firmware upgrades can be downloaded through the communications port, without opening the instrument.

The 19plus V2 samples continuously at up to 4 scans per second (4 Hz) (2 Hz with Digiquartz®), is battery-powered and self-recording, and is commonly used in the field without a computer, recording up to 1000 individual profiles. Data can be uploaded and processed later, as well as transmitted to a PC in real time for acquisition and display using Seasoft software provided (cable length dependent on number of auxiliary sensors, sampling and baud rate, and cable properties). The 19plus V2 can supply power to 7 external sensors and log their outputs with each CTD scan. Nine D-size alkaline batteries provide up to 60 hours of continuous operation when logging C, T, and P at 4 Hz.

The 19plus V2 is easily integrated with an SBE 32 Carousel Water Sampler and is ideal for integration with the SBE 55 ECO Water Sampler. Both real-time and autonomous auto-fire operations are possible with any Sea-Bird CTD / Water Sampler system.

In moored mode, the 19plus V2 records time series measurements at user-programmable intervals (10 seconds to 4 hours). Moored mode is easily configured with setup commands and by removing the profiling T-C Duct and installing optional anti-foulant devices. (If profiling not needed, the 16plus V2 SeaCAT Recorder offers greater moored-mode flexibility.)

CONFIGURATION, OPTIONS, AND ACCESSORIES

A standard SBE 19plus V2 is supplied with plastic housing for depths to 600 meters, strain-gauge pressure sensor, 64 Mbyte FLASH RAM memory, alkaline batteries, glass-reinforced epoxy bulkhead connectors, SBE 5M miniature pump with plastic housing, and T-C Duct.

Options and accessories include:

* pH sensor for integration in Profiling mode only; not applicable to Moored mode

SOFTWARE

The SBE 19plus V2 is supplied with a powerful Windows 2000/XP software package, Seasoft©V2, which includes programs for communication and data retrieval, real-time data acquisition and display, and data processing (filtering, aligning, averaging) and plotting.

  Measurement Range Initial Accuracy Typical Stability Resolution
Conductivity (S/m) 0 - 9 ± 0.0005 0.0003
 S/m/month
0.00005 (most oceanic waters; resolves 0.4 ppm in salinity)
0.00007 (high salinity waters; resolves 0.4 ppm in salinity)
0.00001 (fresh waters; resolves 0.1 ppm in salinity)
Temperature (°C) -5 to +35 ± 0.005 0.0002
°C/month
0.0001
Pressure Strain-Gauge 0 to 20 / 100 / 350 / 600 / 1000 / 2000/ 3500 / 7000 meters ± 0.1% of full scale range 0.1% of full scale range/year 0.002% of full scale range
Pressure
Quartz  (optional)
0 to  20 / 60 / 130 / 200 / 270 / 680 / 1400 / 2000 / 4200 / 7000 / 10500 meters ± 0.02% of full scale range 0.02% of full scale range/year 0.0025% of full scale range

 

Memory: 64 Mbyte non-volatile FLASH memory

Data Storage:

Recorded Parameter Bytes/Sample
T + C 6
Pressure strain-gauge or Quartz 5
each external voltage 2
auxiliary RS-232 sensor sensor dependent

 

Real-Time Clock: 32,768 Hz TCXO accurate to ±1 minute/year

Internal Batteries: 9 alkaline D-cells (Duracell MN1300, LR20) provide 60 hours profiling; optional 9-cell NiMH battery pack provides 40 hours profiling per charge

External Power Supply: 9 - 28 VDC; consult factory for required current

Power Requirements:
Sampling: 70 mA
SBE 5M pump: 100 mA
Optional SBE 5T or 5P pump: 150 mA
Communications: 65 mA
Quiescent: 20 µA

Auxiliary Voltage Sensors:
Auxiliary power out: up to 500 mA at 10.5 - 11 VDC
A/D resolution: 14 bits
Input range: 0 - 5 VDC

Depth Rating, Housing, and Weight:

Depth Rating Housing Material Weight in air
(without pump) *
Weight in water
(without pump) *
600 m (1950 ft) acetal copolymer plastic 7.3 kg (16 lbs) 2.3 kg (5 lbs)
7000 m (22,900 ft) 3AL-2.5V titanium 13.7 kg (30 lbs) 8.6 kg (19 lbs)
* Weights listed are without pump; pump adds (in air) 0.3 to 0.7 kg (0.6 to 1.5 lbs), depending on pump model selected. See pump brochures (SBE 5M or 5T & 5P) for details.

 

Optional Cage:
(for 19plus V2 with strain gauge pressure) 1016 x 241 x 279 mm (40 x 9.5 x 11 inches), 6.3 kg (14 lbs)  (see drawing 22009)
(for 19plus V2 with Digiquartz pressure) 1219 x 241 x 279 mm (48 x 9.5 x 11 in.)  (see drawing 22010)

 

The list below includes (as applicable) the current product brochure, manual, and quick guide; software manual(s); and application notes.

For older SBE 19plus V2 product manuals, organized by instrument firmware version, click here.

Title Type Publication Date PDF File
SBE 19plus V2 Brochure Product Brochure Monday, April 25, 2011 19plusV2brochureApr11.pdf
SBE 19plus V2 Manual Product Manual Monday, September 30, 2013 19plusV2_011.pdf
NiMH Battery Pack and Charger Manual Product Manual Wednesday, December 23, 2009 NiMH_004.pdf
Seasave V7 Manual Software Manual Tuesday, March 18, 2014 Seasave_7.23.2.pdf
SBE Data Processing Manual Software Manual Tuesday, March 18, 2014 SBEDataProcessing_7.23.2.pdf
SBE 19plus V2 Quick Guide Product Quick Guide Thursday, May 24, 2012 19plusV2_referencesheet_006.pdf
Seasave V7 Quick Guide Software Quick Guide Tuesday, August 3, 2010 Seasave_ReferenceSheet_001.pdf
Technical Note: Avoiding Oil Contamination on Deployment in Oil Spill Technical Note Thursday, June 3, 2010 AvoidOilContaminationOnDeployment-General.pdf
Technical Note: Cleaning for CTDs used in Oil Spill Technical Note Thursday, July 21, 2011 SimpleCleaningProtocols_OilSpillRecovery_Jul2011.pdf
Technical Note: Oil Spill Deployment Protocols for SBE 19, 19plus, 19plus V2 CTD Technical Note Thursday, June 3, 2010 SBE19series_OilSpillDeploymentProtocols.pdf
AN02D: Instructions for Care and Cleaning of Conductivity Cells Application Notes Monday, March 10, 2014 appnote2DMar14.pdf
AN06: Determination of Sound Velocity from CTD Data Application Notes Tuesday, February 2, 2010 appnote06Aug04.pdf
AN10: Compressibility Compensation of Sea-Bird Conductivity Sensors Application Notes Tuesday, May 7, 2013 appnote10May13.pdf
AN12-1: Pressure Port Oil Refill Procedure and Nylon Capillary Fitting Replacement Application Notes Friday, September 12, 2008 appnote12-1Sep08.pdf
AN14: 1978 Practical Salinity Scale Application Notes Thursday, January 12, 1989 appnote14.pdf
AN16: Entering Calibration Coefficients for D&A Instruments (Campbell Scientific) OBS-3 Optical Backscatter Sensor Application Notes Thursday, September 18, 2014 appnote16Sep14.pdf
AN21: Instructions for Use of Nickel-Cadmium Battery Packs Application Notes Saturday, February 13, 2010 appnote21Feb10.pdf
AN27D: Minimizing Strain Gauge Pressure Sensor Errors Application Notes Thursday, February 13, 2014 appnote27DFeb14.pdf
AN31: Computing Temperature and Conductivity Slope and Offset Correction Coefficients from Laboratory Calibrations and Salinity Bottle Samples Application Notes Monday, February 22, 2010 appnote31Feb10.pdf
AN34: Instructions for Use of Conductivity Cell Filling and Storage Device PN 50087 and 50087.1 Application Notes Saturday, October 13, 2012 appnote34Oct12.pdf
AN38: TC Duct Fundamentals Application Notes Tuesday, July 10, 2012 appnote38Jul12.pdf
AN42: ITS-90 Temperature Scale Application Notes Thursday, February 13, 2014 appnote42Feb14.pdf
AN43: Universal Ni-Cad Battery Charger Operating Instructions Application Notes Friday, January 13, 1995 appnote43.pdf
AN57: Connector Care and Cable Installation Application Notes Tuesday, May 13, 2014 appnote57Jan14.pdf
AN59: A Load-Bearing Underwater Cable for Hand-Hauled, Real-Time Profiling Application Notes Thursday, October 11, 2012 appnote59Oct12.pdf
AN64-1: Plumbing Installation - SBE 43 DO Sensor and Pump on a CTD Application Notes Wednesday, April 16, 2008 appnote64-1Apr08.pdf
AN67: Editing Sea-Bird .hex Data Files Application Notes Monday, October 15, 2001 appnote67.pdf
AN68: Using USB Ports to Communicate with Sea-Bird Instruments Application Notes Friday, October 19, 2012 appnote68Oct12.pdf
AN69: Conversion of Pressure to Depth Application Notes Monday, July 1, 2002 appnote69.pdf
AN71: Desiccant Use and Regeneration (drying) Application Notes Wednesday, January 15, 2014 Appnote71Jan14.pdf
AN72-V2: Setting Up WET Labs ECO Sensor with Bio-Wiper™ for integration with SeaCATplus V2 CTDs (SBE 16plus V2, 16plus-IM V2, 19plus V2) Application Notes Tuesday, April 15, 2014 Appnote72-V2Apr14.pdf
AN73: Using Instruments with Pressure Sensors at Elevations Above Sea Level Application Notes Friday, February 28, 2014 appnote73Feb14.pdf
AN83: Deployment of Moored Instruments Application Notes Friday, February 14, 2014 appnote83Feb14.pdf
AN84: Using Instruments with Druck Pressure Sensors in Muddy or Biologically Productive Environments Application Notes Tuesday, January 14, 2014 appnote84Jan14.pdf
AN90: Absolute Salinity and TEOS-10: Sea-Bird's Implementation Application Notes Tuesday, September 3, 2013 AppNote90Sep13.pdf
AN95: Setting Up Teledyne Benthos Altimeter with Sea-Bird Profiling CTD Application Notes Sunday, January 12, 2014 Appnote95.pdf
Deployment Endurance Calculator is an aid for quickly determining the maximum deployment length for a moored instrument, based on battery capacity. Deployment Endurance Calculator is part of our Seasoft V2 software suite.
Version 1.6 released September 2, 2014
DeploymentEnduranceCalcV1_6.exe for Windows XP/Vista/7


SeatermV2© is a terminal program launcher for setup and data upload of Sea-Bird instruments developed or redesigned in 2006 and later. The common feature of this generation of instruments is the ability to output status responses in XML. SeatermV2 is part of our Seasoft V2 software suite.
Version 2.4.1 released September 2, 2014
SeatermV2_4_1.exe for Windows XP/Vista/7


SeatermAF© is a terminal program for setup and data upload of Sea-Bird instruments that include Auto-Fire capability for operating a water sampler autonomously on non-conducting cable. SeatermAF is part of our Seasoft V2 software suite.
Version 2.14 released September 17, 2013
SeatermAF_V2_1_4.exe for Windows XP/Vista/7


Seasave V7© acquires, converts, and displays real-time or archived raw data from Sea-Bird profiling CTDs and thermosalinographs, as well as the SBE 16 family of moored CTDs. Seasave V7 is part of our Seasoft V2 software suite.
Version 7.23.2 released March 18, 2014
SeasaveV7_23_2.exe for Windows XP/Vista/7


SBE Data Processing© consists of modular, menu-driven routines for converting, editing, processing, and plotting of oceanographic data acquired with Sea-Bird profiling CTDs, thermosalinographs, and the SBE 16 and 37 families of moored CTDs. SBE Data Processing is part of our Seasoft V2 software suite.
Version 7.23.2 released March 18, 2014
SBEDataProcessing_Win32_V7_23_2.exe for Windows XP/Vista/7


I sent my conductivity sensor to Sea-Bird for calibration, and you also performed a Cleaning and Replatinizing (C &P). You sent the instrument back with 2 sets of calibration data. What does this mean?

The post-cruise calibration contains important information for drift calculations. The post-cruise calibration is performed on the cell as we received it from you, and is an indicator of how much the sensor has drifted in the field. Information from the post-cruise calibration can be used to adjust your data, based on the sensor’s drift over time. See Application Note 31: Computing Temperature and Conductivity Slope and Offset Correction Coefficients from Laboratory Calibrations and Salinity Bottle Samples.

If the sensor has drifted significantly (based on the data from the post-cruise calibration), Sea-Bird performs a C & P to restore the cell to a state similar to the original calibration. After the C & P, the sensor is calibrated again. This calibration serves as the starting point for future data, and for the sensor’s next drift calculation.

The C & P tends to return the cell to its original state. However, there are many subtle factors that may result in the post-C & P calibration not exactly matching the original calibration. Basically, the old platinizing is stripped off and new platinizing is plated on. Anything in this process that alters the cell slightly will result in a difference from the original calibration. We compare the calibration after C & P with the original calibration, not to make any drift analysis, but to make sure we did not drastically alter the cell, or that the cell was not damaged during the C & P process.

Is it necessary to put my instrument in water to test it? Will I destroy the conductivity cell if I test it in air?

It is not necessary to put the instrument in water to test it. It will not hurt the conductivity cell to be in air.

If there is a pump on the instrument, it should not be run for extended periods in air.

  • Profiling instruments (SBE 9plus, 19, 19plus, 19plus V2, 25, 25plus, 49) and some moored instruments (all pumped MicroCATs with integral dissolved oxygen (DO), and pumped MicroCATs without DO with firmware 3.0 and later) do not turn on the pump unless the conductivity frequency is above a specified minimum value (minimum value is hard-wired in 9plus, user-programmable in other instruments). This prevents the pump from turning on in air. See the instrument manual for details.
  • If your instrument does not check for conductivity frequency before turning on the pump: 
    - For moored SeaCATs (16, 16plus, 16plus-IM, 16plus V2, 16plus-IM V2): Disconnect the pump cable for the test. 
    - For older pumped MicroCATs: orient the MicroCAT to provide an upright U-shape for the plumbing. Then fill the inside of the pump head with water via the pump exhaust tubing; this will provide enough lubrication to prevent pump damage during brief testing.

Which Sea-Bird profiling CTD is best for my application?

Sea-Bird makes four main profiling CTD instruments, as well as several profiling CTD instruments for specialized applications.

In order of decreasing cost, the four main profiling CTD instruments are the SBE 911plus CTD, SBE 25plus Sealogger CTD, SBE 19plus SeaCAT Profiler CTD, and SBE 49 FastCAT CTD Sensor:

  • The SBE 911plus is the world’s most accurate CTD. Used by most leading oceanographic institutions, the SBE 911plus is recognized for superior performance, reliability, and ease-of-use. Features include: modular conductivity and temperature sensors, Digiquartz pressure sensor, TC-Ducted Flow and pump-controlled time response, 24 Hz sampling, 8 A/D channels and power for auxiliary sensors, modem channel for real-time water sampler control without data interruption, and optional 9600 baud serial data uplink. The SBE 911plus system consists of: SBE 9plus Underwater Unit and SBE 11plus Deck Unit. The SBE 9plus can be used in self-contained mode when integrated with the optional SBE 17plus V2 Searam. The Searam provides battery power, internal 24 Hz data logging, and an auto-fire interface to an SBE 32 Carousel Water Sampler to trigger bottle closures at pre-programmed depths.
  • The SBE 25plus Sealogger is the choice for research work from smaller vessel not equipped for real-time operation, or use by multi-discipline scientific groups requiring configuration flexibility and good accuracy and resolution on a smaller budget. The SBE 25plus is a battery-powered, internally-recording CTD featuring the same modular C & T sensors used on the SBE 9plus CTD, an integral strain gauge pressure sensor, 16 Hz sampling, 2 GB of memory, TC-Ducted Flow and pump-controlled time response, and 8 A/D channels plus 2 RS-232 channels and power for auxiliary sensors. Real-time data can be transmitted via RS-232 simultaneous with data recording. The SBE 25plus integrates easily with an SBE 32 Carousel Water Sampler or SBE 55 ECO Water Sampler for real-time or autonomous operation.
  • The SBE 19plus V2 SeaCAT Profiler is known throughout the world for good performance, reliability, and ease-of-use. An economical, battery-powered, internally-recording mini-CTD, the SBE 19plus V2 is a good choice for basic hydrography, fisheries research, environmental monitoring, and sound velocity profiling. Features include 4 Hz sampling, 6 differential A/D channels plus 1 RS-232 channel and power for auxiliary sensors, 64 MB of memory, and pump-controlled conductivity time response. Real-time data can be transmitted via RS-232 simultaneous with data recording, The SBE 19plus V2 integrates easily with an SBE 32 Carousel Water Sampler or SBE 55 ECO Water Sampler for real-time or autonomous operation.
  • The SBE 49 FastCAT is an integrated CTD sensor intended for towed vehicle, ROV, AUV, or other autonomous profiling applications. Real-time data ‑ in raw format or in engineering units ‑ is logged or telemetered by the vehicle to which it is mounted. The SBE 49’s pump-controlled, TC-ducted flow minimizes salinity spiking, and its 16 Hz sampling provides very high spatial resolution of oceanographic structures and gradients. The SBE 49 has no memory or internal batteries. The SBE 49 integrates easily with an SBE 32 Carousel Water Sampler or SBE 55 ECO Water Sampler for real-time operation.

The specialized profiling CTD instruments are the SBE 52-MP Moored Profiler, Glider Payload CTD, and SBE 41/41CP Argo CTD module:

  • The SBE 52-MP Moored Profiler is a conductivity, temperature, pressure sensor, designed for moored profiling applications in which the instrument makes vertical profile measurements from a device that travels vertically beneath a buoy, or from a buoyant sub-surface sensor package that is winched up and down from a bottom-mounted platform. The 52-MP's pump-controlled, TC-ducted flow minimizes salinity spiking. The 52-MP can optionally be configured with an SBE 43F dissolved oxygen sensor.
  • The Glider Payload CTD measures conductivity, temperature, and pressure, and optionally, dissolved oxygen (with the modular SBE 43F DO sensor). It is a modular, low-power profiling instrument for autonomous gliders with the high accuracy necessary for research, inter-comparison with moored observatory sensors, updating circulation models, and leveraging data collection opportunities from operational vehicle missions. The pressure-proof module allows glider users to exchange CTDs (and DO sensors) in the field without opening the glider pressure hull.
  • Argo floats are neutrally buoyant at depth, where they are carried by currents until periodically increasing their displacement and slowing rising to the surface. The SBE 41/41CP CTD Module obtains the latest CTD profile each time the Argo float surfaces. At the surface, the float transmits in-situ measurements and drift track data to the ARGOS satellite system. The SBE 41/41CP can be integrated with Sea-Bird's Navis floatNavis float with Biogeochemical Sensors, or floats from other manufacturers. The SBE 41N CTD is integrated with Sea-Bird's Navis Float with Integrated Biogeochemical Sensors.

See Product Selection Guide for a table summarizing the features of our profiling CTDs.

How can I tell if the conductivity cell on my CTD is broken?

Conductivity cells are made of glass, which is breakable.

  • If a cell is cracked, it typically causes a salinity shift or erratic data.
  • However, if the crack occurs at the end of the cell, the sensor will continue to function normally until water penetrates the epoxy jacket. Post-cruise calibration results will reveal whether or not water has penetrated the epoxy jacket.

Inspect the cell thoroughly and make sure that it isn’t cracked or abused in any way.

  • (SBE 9plus, 25, or 25plus) If the readings are good at the surface but erratic at depth, it is likely that the problem is in the cable or the connector, not the conductivity cell. Check the connections, making sure that you burp the connectors when you plug them in (see Application Note 57: Connector Care and Cable Installation). Check the cable itself (swap with a spare cable, if available).
  • If the readings are incorrect at the surface but good after a few meters, it is likely that the problem is flow-related. Verify that the pump is working properly. Check the air bleed valve (the white plastic piece in the Y-fitting, which is installed on vertically deployed CTDs) to see if it is clogged; clean out the small hole with a piece of fine wire supplied with your CTD.
  • If the readings are incorrect for the entire cast, there may be an incorrect calibration coefficient or the cell may be cracked.
  • Check the conductivity calibration coefficients in the configuration (.con or .xmlcon) file.
  • Do a frequency check on the conductivity cell. Disconnect the plumbing on the cell. Rinse the cell with distilled or de-ionized water and blow it dry (use your mouth and not compressed air, as there tends to be oil in the air lines on ships). With the cell completely dry, check the frequency reading. It should read within a few tenths of a Hz of the 0 reading on your Calibration Sheet. If it does not, something is wrong with the cell and it needs to be repaired.

Can I use a pressure sensor above its rated pressure?

Digiquartz pressure sensors are used in the SBE 9plus, 53, and 54. The SBE 16plus V2, 16plus-IM V2, 19plus V2, and 26plus can be equipped with either a Druck pressure sensor or a Digiquartz pressure sensor. All other instruments that include pressure use a Druck pressure sensor.

  • The overpressure rating for a Digiquartz (as stated by Paroscientific) is 1.2 * full scale. The sensor will provide data values above 100% of rated full scale; however, Sea-Bird does not calibrate beyond the rated full scale.
  • The overpressure rating for a Druck (as stated by Druck) is 1.5 * full scale. The sensor will provide data values above 100% of rated full scale; however, Sea-Bird does not calibrate beyond the rated full scale.

Note: If you use the instrument above the rated range, you do so at your own risk; the product will not be covered under warranty.

I want to integrate a moored CTD with some auxiliary sensors (transmissometer, fluorometer, etc.). Which CTD should I use?

Sea-Bird currently manufactures only 1 moored CTD that can accept auxiliary sensors, the SBE 16plus V2 SeaCAT (and its inductive modem version, the 16plus-IM V2). These instruments measure conductivity and temperature; a pressure sensor is optional. They have 6 differential A/D channels and 1 RS-232 channel available for auxiliary sensors, which can be plugged into the CTD end cap.

The SBE 37 MicroCAT family includes CTDs that are integrated with a dissolved oxygen sensor at the factory.

Notes:

  • The SBE 19plus V2 SeaCAT, intended primarily for profiling applications, can also be used in moored mode. The 19plus V2 also has 6 differential A/D channels and 1 RS-232 channel available for auxiliary sensors. When in moored mode, it functions similar to a 16plus V2 with optional pressure sensor.
  • The older versions of these products, the SBE 16 / 16plus / 16plus-IM and SBE 19 / 19plus, also accept auxiliary sensors.

See Product Selection Guide for a table summarizing the features of all our moored instruments.

What are the major steps involved in taking a cast with a Profiling CTD?

Following is a brief outline of the major steps involved in taking a CTD cast, based on generally accepted practices. However, each ship, crew, and resident technicians have their own operating procedures. Each scientific group has their own goals. Therefore, observe local ship and scientific procedures, particularly in areas of safety. Before the cruise a discussion of the planned work is advisable between the ship’s crew, resident technicians, and scientific party. At this time discuss and clarify any specific ship’s procedures.

Note: The following procedure was written for an SBE 9plus CTD operating with an SBE 11plus Deck Unit. Modify the procedure as necessary for your CTD.

10 to 15 minutes before Station:

  1. Review the next cast’s plan, including proposed maximum cast depth, bottom depth, and number of bottles to close and depths. If the cast will be close to the bottom, familiarize yourself with the bottom topography.
  2. Verify that all water samples have been obtained from the bottles from the previous cast. If so, drain the bottles and cock them. Hand manipulate each Carousel latch as you cock the bottle to ensure it is free to release and is not stuck in some way.
  3. Remove the soaker tubes from the conductivity cells.
  4. Remove any other sensor covers.
  5. With permission from the deck crew, power up the CTD. Check the Deck Unit front panel display to verify communication. Perform a quick frequency check of the main sensors.
  6. Start Seasave. Set up a fixed display. Select Do not archive data for this cast. Start acquisition and view the data to verify the system is operational.
  7. Clean optical sensor windows, and perform any required air calibration.
  8. Stop acquisition. Do Not turn the CTD Deck Unit off. Select begin archiving data immediately. Set up the plot scales and status line.

5 minutes before Station:

  1. Start the ship's depth sounder and obtain a good depth reading. Be careful reading the depth sounder; if it is improperly configured the trace will wrap around the plot and be incorrect. The bottom depth should be close to the expected charted depth.
  2. Fill out any parts of the cast log that can be done at this time.

On Station, On Deck:

  1. Verify the position and the bottom depth.
  2. The computer operator should begin filling out the software header.
  3. After receiving word from the bridge that they are on station and ready to begin, untie the CTD and move it into position. If this requires hydraulics, ensure you have the appropriate people in place and permission.
  4. Position the CTD under the block. Have the winchman remove any slack from the wire.
  5. Notify the computer room that the CTD is ready for launch. The computer room should start acquiring data.
  6. Obtain a barometric pressure reading and note it on the cast sheet.
  7. When the bridge, computer room, and winchman are ready (and you have permission to proceed), put the CTD in the water.
  8. Have the winchman lower the CTD to 10 meters (his readout), hold for 1 minute, and then bring it back to the surface. One operator should remain on deck to help the winchman see when to stop the CTD. The CTD should be far enough below the surface so that the package does not break the surface in the swells.

CTD Soaking at the Surface:

  1. Finish filling out the cast log. Re-check the bottom depth.
  2. Fill out the computer software log.
  3. Hold the CTD at the surface for at least 3 minutes.
  4. Check the status line to verify that the CTD values are correct. The pressure should be the soaking depth of the CTD. Comparing the CTD temperature and salinity to the ship's thermosalinograph is helpful. Log the information (CTD and thermosalinograph) on the cast sheet.

Starting the Cast:

  1. Call the winchman and have him start the cast down. Typical lowering speed is 1 m/sec, modified for conditions as needed.
  2. Watch the computer output and verify that the system is working.

During the Cast:

  1. Closely monitor the CTD output for malfunctions. Sudden noise in a channel is often a sign of a leaking cable. A periodically flashing error light on the Deck Unit is a sign of a bad spot in the slip rings. The modulo error count (usually on the status line) provides an indication of telemetry integrity; on a properly functioning system, there will be no modulo errors.
  2. Note any odd behavior or problems on the cast sheet. Keeping good notes and records is of critical importance. While you may remember what happened an hour from now, in the months that follow, these notes will be a vital link to the cruise as you process the data.
  3. Monitor the bottom depth. This is especially critical if the cast will be close to the bottom, or you are working in an area with varying topography such as in a canyon. Running the CTD into the bottom can cause serious (and expensive) damage.

Approaching the Bottom:

  1. Take extra care if the cast will take the CTD close to the bottom. Monitor the bottom depth, pinger, and altimeter, if available. As you get within 30 meters of the bottom, slow down the cast to 0.5 m/sec. If you wish to get closer than 10 m above the bottom, slow down to 0.2 m/sec. Keep in mind that ship roll will cause the CTD depth to oscillate by several meters.
    - If the CTD does touch bottom, it will be apparent from the sudden, low salinity spike. A transmissometer, if installed, will also show a sudden low spike.
  2. Adjust these numbers and procedures as conditions dictate to avoid crashing the CTD into the bottom.
  3. When the CTD reaches the maximum cast depth, call the winchman and stop the descent.
  4. Log a position on the cast sheet. If a bottle will be closed at the bottom, allow the CTD to soak for at least 1 minute (preferably several minutes) and then close the bottle. Verify that the software records the bottle closure confirmation.
  5. Start the CTD upcast. Stop the CTD ascent at any other bottle closure depths. For each bottle, soak for at least 1 minute (preferably several minutes) and then close the bottle.

End of the Cast:

  1. As the CTD approaches the surface, have someone help spot for the winchman. Stop the CTD below the surface. Close a bottle if desired.
  2. When ready, recover the CTD. Avoid banging the system against the ship.

CTD Back on Board:

  1. Stop data acquisition and power off the CTD.
  2. Move the CTD it into its holding area and secure it.
  3. See Application Note 2D: Instructions for Care and Cleaning of Conductivity Cells for details on rinsing, cleaning, and storing the conductivity cell. Fill the conductivity cell with clean DI (or 1% Triton-X) and secure the filler device to the CTD frame. Freezing water in a conductivity cell will break the cell.
  4. See Application Note 64: SBE 43 Dissolved Oxygen Sensor - Background Information, Deployment Recommendations, and Cleaning and Storage for details on rinsing, cleaning, and storing SBE 43 (membrane-type) dissolved oxygen sensors; see the SBE 63 manual for details on rinsing, cleaning, and storing SBE 63 optical dissolved oxygen sensors.
  5. Rinse any optical sensors.
  6. Rinse the water sampler latches with clean water.
  7. Draw water samples from the bottles.

After the Cast:

  1. Re-plot the data and look at any channels that were not displayed in real time.
  2. Perform diagnostics and take a first pass through processing.
    - Verify that the data is good (at least on a first-order basis) at this point, when you can still re-do the cast. Many casts are lost because they are not analyzed until months later, when the problems are discovered.
  3. Final processing may need to wait until bottle salts and post-cruise lab calibrations are available.

How do instruments handle external power if internal batteries are installed?

Most Sea-Bird instruments that are designed to be powered internally or externally incorporate diode or'd circuitry, allowing only the voltage that has the greater potential to power the instrument. You can power the instrument externally without running down the internal batteries. This allows you to lab test using external power that has higher voltage than the internal batteries, and then deploy using internal power, knowing that the internal batteries are fresh.

For the SBE 25plus, if external power of 14 volts or higher is applied, the 25plus runs off of the external power, even if the main battery voltage is higher.

How should I pick the pressure sensor range for my CTD? Would the highest range give me the most flexibility in using the CTD?

While the highest range does give you the most flexibility in using the CTD, it is at the expense of accuracy and resolution. It is advantageous to use the lowest range pressure sensor compatible with your intended maximum operating depth, because accuracy and resolution are proportional to the pressure sensor's full scale range. For example, the SBE 9plus pressure sensor has initial accuracy of 0.015% of full scale, and resolution of 0.001% of full scale. Comparing a 2000 psia (1400 meter) and 6000 psia (4200 meter) pressure sensor:

  • 1400 meter pressure sensor ‑ initial accuracy is 0.21 meters and resolution is 0.014 meters
  • 4200 meter pressure sensor ‑ initial accuracy is 0.63 meters and resolution is 0.042 meters

Should I collect water samples (close bottles) on the downcast or the upcast?

Most of our CTD manuals refer to using downcast CTD data to characterize the profile. For typical configurations, downcast CTD data is preferable, because the CTD is oriented so that the intake is seeing new water before the rest of the package causes any mixing or has an effect on water temperature.

However, if you take water samples on the downcast, the pressure on an already closed bottle increases as you continue through the downcast; if there is a small leak, outside water is forced into the bottle, contaminating the sample with deeper water. Conversely, if you take water samples on the upcast, the pressure decreases on an already closed bottle as you bring the package up; any leaking results in water exiting the bottle, leaving the integrity of the sample intact. Therefore, standard practice is to monitor real-time downcast data to determine where to take water samples (locations with well-mixed water and/or with peaks in the parameters of interest), and then take water samples on upcast.

What is the maximum cable length for real-time RS-232 data?

Cable length is one of the most misunderstood items in the RS-232 world. The RS-232 standard was originally developed decades ago for a 19200 baud rate, and defines the maximum cable length as 50 feet, or the cable length equal to a capacitance of 2500 pF. The capacitance rule is often forgotten; using a cable with low capacitance allows you to span longer distances without going beyond the limitations of the standard. Also, the maximum cable length mentioned in the standard is based on 19200 baud rate; if baud is reduced by a factor of 2 or 4, the maximum length increases dramatically. Using typical underwater cables, allowable combinations of cable length and baud rate for Sea-Bird instruments communicating with RS-232 are shown below:

Maximum Cable Length (meters) Maximum Baud Rate*
1600 600
800 1200
400 2400
200 4800
100 9600
50 19,200
25 38,400
16 57,600
8 115,200

*Note: Consult instrument manual for baud rates supported for your instrument.

 

I am ordering a CTD and want to use auxiliary sensors. Should I order them from Sea-Bird also, or deal directly with the sensors’ manufacturers?

This depends on your own expertise and resources. We have extensive experience in integrating and supporting a wide range of auxiliary sensors, but not everything under the sun. We have a large list of commonly used sensors that we routinely offer for sale (see Third Party Sensor Configuration).

When you purchase any of these auxiliary sensors from Sea-Bird, we are able to apply this experience to integrating the sensors with the CTD. The integration includes installing the sensors (with appropriate mounting kits and cables) in a manner that puts each sensor in the best possible orientation for optimum performance. It also includes configuring the CTD system and software to accept the sensors’ inputs and properly display the data, and testing the entire system, typically in a chilled saltwater bath overnight, to confirm proper operation. Having done the integration, we also support the entire system in terms of follow-on service and end-user support with operational and data analysis questions *. There is significant added value in our integration service, and there is some extra cost for this, compared to doing it yourself. However, we do not base our business on selling services, and the prices charged for Third Party sensors carry minimal mark-ups that vary depending on the pricing we are offered by the manufacturers. In some cases we can sell at the manufacturer's list price, and in others we have to add margin.

*Notes:
1. As described in our Warranty, auxiliary sensors manufactured by other companies are warranted only to the limit of the warranties provided by their original manufacturers (typically 1 year).
2. Click here for information on repairing / recalibrating auxiliary sensors manufactured by other companies.

Can I deploy my profiling CTD for monitoring an oil spill?

Sea-Bird CTDs can be deployed in oil; the oil will not cause long-term damage to the CTD. If the oil coats the inside of the conductivity cell and coats the dissolved oxygen sensor membrane, it can possibly affect the sensor’s calibration (and thus affect the measurement and the data). Simple measures can reduce the impact, as follows:

  1. To minimize the ingestion of oil into the conductivity cell and onto the DO sensor membrane:

SBE 19, 19plus, 19plus V2, 25, or 25plus CTD:

Set up the CTD so that the pump does not turn on until the CTD is in the water and below the layer of surface oil, minimizing ingestion of oil (however, some oil will still enter the system). Pump turn-on is controlled by two user-programmable parameters: the minimum conductivity frequency and the pump delay.

Set the minimum conductivity frequency for pump turn-on above the instrument’s zero conductivity raw frequency (shown on the conductivity sensor Calibration Sheet), to prevent the pump from turning on when the CTD is in air. Note that this is the same as our typical recommendation for setting the minimum conductivity frequency.
     For salt water and estuarine applications - typical value = zero conductivity raw frequency + 500 Hz
     For fresh/nearly fresh water - typical value = zero conductivity raw frequency + 5 Hz
If the minimum conductivity frequency is too close to the zero conductivity raw frequency, the pump may turn on when the CTD is in air as result of small drifts in the electronics. Another option is to rely only on the pump turn-on delay time to control the pump; if so, set a minimum conductivity frequency lower than the zero conductivity raw frequency.

Set the pump turn-on delay time to allow enough time for you to lower the CTD below the surface oil layer after the CTD is in the water (the CTD starts counting the pump delay time after the minimum conductivity frequency is exceeded). You may need to set the pump delay time to be longer than our typical 30-60 second recommendation.

The current minimum conductivity frequency and pump delay can be checked by sending the status command to the CTD (DS or GetCD, as applicable). Commands for modifying these parameters are:

  • SBE 19: SP (SBE 19 responds with prompts for setting up these parameters)
  • SBE 19plus and 19plus V2: MinCondFreq=x and PumpDelay=x (where x is the value you are programming).
  • SBE 25: CC (SBE 25 responds with a series of setup prompts, including setting up these parameters)
  • SBE 25plus: SetMinCondFreq=x and SetPumpDelay=x (where x is the value you are programming).

SBE 9plus CTD:

Minimum conductivity frequency and pump delay are not user-programmable for the 9plus. 

If you are using your 9plus with the 11plus Deck Unit, the Deck Unit provides power to the 9plus. Without power, the pump will not turn on. At the start of the deployment, to ensure that you have cleared the surface oil layer before the pump turns on, do not turn on the Deck Unit until the 9plus is below the surface oil layer. Similarly, on the upcast, turn off the Deck Unit before the 9plus reaches the surface oil layer.

If your 9plus is equipped with the optional manual pump control, you can enable manual pump control via the Pump Control tab in Seasave V7’s Configure Inputs dialog box. Once enabled, you can turn the pump on and off from Seasave V7’s Real-Time Control menu. Do not turn the pump on until the CTD is below the surface oil layer. On the upcast, turn the pump off before the CTD reaches the surface oil layer.

  1. To reduce the effect of the ingestion of oil into the conductivity cell and onto the DO sensor membrane or optical window:

After each recovery, rigorously follow the cleaning and storage procedures in the following application notes ‑

  • Application Note 2D: Instructions for Care and Cleaning of Conductivity Cells
  • Application Note 64: SBE 43 Dissolved Oxygen Sensor – Background Information, Deployment Recommendations, and Cleaning and Storage
  • SBE 63 Optical Dissolved Oxygen Sensor manual

Quick Reference Sheets for Oil Spill Deployment:

Do you recommend a particular brand of alkaline D-cell batteries?

For Sea-Bird instruments that use alkaline D-cells, Sea-Bird uses Duracell MN 1300, LR20. While rare, we have seen a few problems with cheaper batteries over the years: they are more likely to leak, may vary in size (leading to loose batteries causing a bad power connection), and may not last as long.

How often do I need to have my instrument and/or auxiliary sensors recalibrated? Can I recalibrate them myself?

General recommendations:

  • Profiling CTD — recalibrate once/year, but possibly less often if used only occasionally. We recommend that you return the CTD to Sea-Bird for recalibration. (In principle, it is possible for calibration to be performed elsewhere, if the calibration facility has the appropriate equipment andtraining. However, the necessary equipment is quite expensive to buy and maintain.) In between laboratory calibrations, take field salinity samples to document conductivity cell drift.
  • Thermosalinograph — recalibrate at least once/year, but possibly more often depending on the degree of bio-fouling in the water.
  • DO sensor —
    — SBE 43 — recalibrate once/year, but possibly less often if used only occasionally and stored correctly (see Application Note 64), and also depending on the amount of fouling and your ability to do some simple validations (see Application Note 64-2)
    — SBE 63 — recalibrate once/year, but possibly less often if used only occasionally and stored correctly and also depending on the amount of fouling and your ability to do some simple validations (see SBE 63 manual)
  • pH sensor — recalibrate every 6 months
  • Transmissometer — usually do not require recalibration for several years. Recalibration at the manufacturer’s factory is the most practical method.

Profiling CTDs:

We often have requests from customers to have some way to know if the CTD is out of calibration. The general character of sensor drift in Sea-Bird conductivity, temperature, and pressure measurements is well known and predictable. However, it is very difficult to know precisely how far a CTD calibration has drifted over time unless you have access to a very sophisticated calibration lab. In our experience, an annual calibration schedule will usually maintain the CTD accuracy to within 0.01 psu in Salinity.

Conductivity drifts as a change in slope as a result of accumulated fouling that coats the inside of the conductivity cell, reducing the area of the cell and causing an under-reporting of conductivity. Fouling consists of both biological growth and accumulated oils and inorganic material (sediment). Approximately 95% of fouling occurs as the cell passes through oil and other contaminants floating on the sea surface. Most conductivity fouling is episodic, as opposed to gradual and steady drift. Most fouling events are small and mostly transitory, but they have a cumulative affect over time. A severe fouling event, such as deployment through an oil spill, could have a dramatic but only partially recoverable effect, causing an immediate jump shift toward lower salinity. As fouling becomes more severe, the fit becomes increasingly non-linear and offsets and slopes no longer produce adequate correction, and return to Sea-Bird for factory calibration is required. Frequently checking conductivity drift is likely to be the most productive data assurance measure you can take. Comparing conductivity from profile to profile (as a routine check) will allow you to detect sudden changes that may indicate a fouling event and the need for cleaning and/or re-calibration.

Temperature generally drifts slowly, at a steady rate and predictably as a simple offset at the rate of about 1-2 millidegrees per year. This is approximately equal to 1-2 parts per million in Salinity error (very small).

Pressure sensor drift is also an offset, and annual comparisons to an accurate barometer to determine offset will generally keep the sensor within specification for several years, particularly as the sensors age over time.

What are the major steps involved in deploying a moored instrument?

Application Note 83: Deployment of Moored Instruments contains a checklist, which is intended as a guideline to assist you in developing a checklist specific to your operation and instrument setup.

I want to add an auxiliary sensor to my CTD (SBE 9plus, 16, 16plus, 16plus-IM, 16plus V2, 16plus-IM V2, 19, 19plus, 19plus V2, 21, 25, or 25plus). Assuming the auxiliary sensor is compatible with the instrument, what is the procedure?

Adding the sensor(s) is reasonably straightforward:

  1. Mount the sensor; a poor mounting scheme can result in poor data.
    Note: If the new sensor will be part of a pumped system, the existing plumbing must be modified; consult Sea-Bird for details.
  2. Attach the new cable.
  3. (not applicable to 9plus used with 11plus Deck Unit) Using the appropriate terminal program — Enable the channel(s) in the CTD, using the appropriate instrument command.
  4. Using Seasave V7 or SBE Data Processing — Modify the CTD configuration (.con or .xmlcon) file to reflect the new sensor, and type in the calibration coefficients.

What are the recommended practices for connectors - mating and unmating, cleaning corrosion, and replacing?

Mating and Unmating Connectors:

It is important to prepare and mate connectors correctly, both in terms of the costs to repair them and to preserve data quality. Leaking connectors cause noisy data and even potential system shutdowns. Application Note 57: Connector Care and Cable Installation describes the proper care and installation of connectors for Sea-Bird instruments. The Application Note covers connector cleaning and cable or dummy plug installation, locking sleeve installation, and cold weather tips.

Checking for Leakage and Cleaning Corrosion on Connectors:

If there has been leakage, it will show up as green-colored corrosion product. Performing the following steps can usually reverse the effect of the leak:

  1. Thoroughly clean the connector with water, followed by alcohol.
  2. Give the connector surfaces a light coating of silicon grease.

Re-mate the connectors properly — see Application Note 57: Connector Care and Cable Installation and 9-minute video covering O-ring, connector, and cable maintenance.

Replacing Connectors:

  • The main concern when replacing a bulkhead connector is that the o-rings on the connector and end cap must be prepared and installed correctly; if they are not, the instrument will flood. See the question below for general procedure on handling o-rings.
  • Use a thread-locking compound on the connector threads to prevent the new connector from loosening, which could also lead to flooding.
  • If the cell guard must be removed to open the instrument, take extra care not to break the glass conductivity cell.

Do I need to remove batteries before shipping my instrument for a deployment or to Sea-Bird?

Alkaline batteries can be shipped installed in the instrument. See Shipping Batteries for information on shipping instruments with Lithium or Nickel-Metal Hydride (NiMH) batteries.

What are the recommended practices for inspecting, cleaning, and replacing o-rings?

Inspecting and Cleaning O-Rings and Mating Surfaces:

  1. Remove any water from the o-rings and mating surfaces with a lint-free cloth or tissue.
  2. Visually inspect the o-rings and mating surfaces for dirt, nicks, cuts, scratches, lint, hair, and any signs of corrosion; these could cause the seal to fail. Clean the surfaces, and clean or replace the o-rings as necessary.
  3. Apply a light, even coat of 100% silicon o-ring lubricant (Parker Super O Lube) to the o-rings and mating surfaces. For an end cap o-ring, a ball of lubricant the size of a pea is about all that is needed. Too much lubricant can cause the seal to fail as much, if not more, than no grease. Do not use petroleum-based lubricant (car grease, Vaseline, etc.), as it will cause premature failure of the rubber.
    CAUTION: Parker makes another product, Parker O Lube, that is petroleum-based. Do not use this product; verify that you are using Parker Super O Lube.
  4. After lubricating the o-ring, immediately reassemble the end cap or connector, verifying that no hairs or lint have collected on the lubricated o-ring.

Replacing O-Rings:

  • End Cap O-Rings: We recommend scheduled replacement of end cap o-rings approximately every 3 years, to prevent leaks caused by normal o-ring wear.
  • Connector O-Rings: Replacing connector o-rings requires de-soldering and re-soldering the connector wires, which makes it a more difficult task. Therefore, we recommend replacement of connector o-rings when needed, not on a routine, scheduled basis.

Additional Information:

  • 9-minute video covering O-ring, connector, and cable maintenance.
  • Short, silent video of application of lubricant to o-ring.
  • Short, silent video of application of lubricant to o-ring mating surface (note the use of a plastic dental syringe — no sharp points to scratch the housing — to apply the lubricant).

Do I need to clean the exterior of my instrument before shipping it to Sea-Bird for calibration?

Remove as much biological material and/or anti-foul coatings as possible before shipping. Sea-Bird cannot place an instrument with a large amount of biological material or anti-foul coating on the housing in our calibration bath; if we need to clean the exterior before calibration, we will charge you for this service.

  • To remove barnacles, plug the ends of the conductivity cell to prevent the cleaning solution from getting into the cell. Then soak the entire instrument in white vinegar for a few minutes. After scraping off the barnacles and marine growth, rinse the instrument well with fresh water.
  • To remove anti-foul paint, use a Heavy Duty Scotch-Brite pad (http://www.3m.com/us/home_leisure/scotchbrite/products/scrubbing_scouring.html) or similar scrubbing device.

What is an Anti-Foulant Device? Does it affect the conductivity cell calibration? How often should I replace it? Does it require special handling?

The Anti-Foulant Device is an expendable device that is installed on each end of the conductivity cell, so that any water that enters the cell is treated. Anti-Foulant Devices are typically used with moored instruments (SBE 16, 16plus, 16plus-IM, 16plus V2, 16plus-IM V2, 37-SM, 37-SMP, 37-SMP-IDO, 37-SMP-ODO, 37-SI, 37-SIP, 37-SIP-IDO, 37-IM, 37-IMP, 37-IMP-IDO, 37-IMP-ODO), thermosalinographs (SBE 21 and 45), glider CTDs (Glider Payload CTD), moored profilers (SBE 52-MP), and drifters (SBE 41/41CP Argo float CTDs), and optionally with SBE 19plus, 19plus V2, and 49 profilers.

Anti-Foulant Devices have no effect on the calibration, because they do not affect the geometry of the conductivity cell in any way. The Anti-Foulant Devices are mounted at either end of the conductivity cell. For an in-depth explanation of how Sea-Bird makes the conductivity measurement, see Conductivity Sensors for Moored and Autonomous Operation.

Useful deployment life varies, depending on several factors. We recommend that customers consider more frequent anti-foulant replacement when high biological activity and strong current flow (greater dilution of the anti-foulant concentration) are present. Moored instruments in high growth and strong dilution environments have been known to obtain a few months of quality data, while drifters that operate in non-photic, less turbid deep ocean environments may achieve years of quality data. Experience may be the strongest determining factor in specific deployment environments. Sea-Bird recommends that you keep track of how long the devices have been deployed, to allow you to purchase and replace the devices when needed.

Shelf Life and Storage: The best way to store Anti-Foulant Devices is in an air-tight, opaque container. The rate of release of anti-foulant is based on saturation of the environment. The anti-foulant will release until the environment is fully saturated (100% saturated) and then it will no longer release any anti-foulant. So if you keep Anti-Foulant Devices sealed well in an air-tight container, theoretically they will stay good for extended periods of time. Exposure to direct sunlight can also affect the release of anti-foulant; we recommend storage in an opaque container.

Handling:

  • For details, refer to the Material Safety Data Sheet, enclosed with the shipment and available on our MSDS page.
  • Anti-Foulant Devices are not classified by the U.S. DOT or the IATA as hazardous material.

I want to change the pressure sensor on my CTD, swapping it as needed to get the best data for a given deployment depth. Can I do this myself, or do I need to send the instrument to Sea-Bird?

On most of our instruments, replacement of the pressure sensor should be performed at Sea-Bird. We cannot extend warranty coverage if you replace the pressure sensor yourself.

However, we recognize that you might decide to go ahead and do it yourself because of scheduling/cost issues. Some guidelines follow:

  1. Perform the swap and carefully store the loose sensor on shore in a laboratory or electronics shop environment, not on a ship. The pressure sensor is fairly sensitive to shock, and a loose sensor needs to be stored carefully. Dropping the sensor will break it.
  2. Some soldering and unsoldering is required. Verify that the pressure sensor is mounted properly in your instrument. Properly re-grease and install the o-rings, or the instrument will flood.
  3. Once the sensor is installed, back-fill it with oil. Sea-Bird uses a vacuum-back filling apparatus that makes this job fairly easy. We can provide a drawing showing the general design of the apparatus, which can be modified and constructed by your engineers.
  4. For the most demanding work, calibrate the sensor on a deadweight tester to ensure proper operation and calibration.
  5. Enter the calibration coefficients for the new sensor in:
  • the CTD configuration (.con or .xmlcon) file, using Seasave V7 or SBE Data Processing, and
  • (for an instrument with internally stored calibration coefficients) the CTD EEPROM, using the appropriate terminal program and the appropriate calibration coefficient commands

Note: This discussion does not apply to the SBE 25 (not 25plus), which uses a modular pressure sensor (SBE 29) mounted externally on the CTD. Swap the SBE 29 as desired, use the CC command in Seaterm or SeatermAF to enter the new pressure range and pressure temperature compensation value, and type the calibration coefficients for the new sensor into the CTD configuration (.con or .xmlcon) file in Seasave V7 or SBE Data Processing.

What are the recommended practices for storing sensors at low temperatures, and deploying at low temperatures or in frazil or pancake ice?

General

Large numbers of Sea-Bird conductivity instruments have been used in Arctic and Antarctic programs.

Special accommodation to keep temperature, conductivity, oxygen, and optical sensors at or above 0 C is advised. Often, the CTD is brought inside protective doors between casts to achieve this.

Conductivity Cell

When freezing is possible, we recommend that the conductivity sensor be stored dry. Remove larger droplets of water by blowing through the cell. Do not use compressed air, which typically contains oil vapor. Attach a length of Tygon tubing to each end of the conductivity cell to close the cell ends. See Application Note 2D: Instructions for Care and Cleaning of Conductivity Cells for details.

There are several considerations to weigh when contemplating deployments at low temperatures in general, and in frazil or pancake ice:

  • Ensure that the instrument is at or above water temperature before it is deployed. If the cell gets colder than 0 to -2 ºC while on deck, when it enters the water a layer of ice forms inside the cell as the cell warms to ocean temperature. If ice forms inside the conductivity cell, measurements will be low of correct until the ice layer melts and disappears. Thin layers of ice will not hurt the conductivity cell, but repeated ice formation on the electrodes will degrade the conductivity calibration (at levels of 0.001 to 0.020 psu) and thicker layers of ice can lead to glass fracture and permanent damage of the cell.
  • For accurate measurements, keep ice out of the sensing region of the conductivity cell. The conductivity measurement involves determining the electrical resistance of the water inside the sensor. Ice is essentially a non-conductor. To the extent that ice displaces the water, the conductivity will register (very) misleadingly low. Some type of screening is necessary to keep ice out of the cell. This is relatively easy to arrange for the Sea-Bird conductivity cell, which is an electrode-type cell, because its sensing region is totally inside a long tube; plastic mesh could be positioned at each end and would have zero effect on accuracy and stability.

The above considerations apply to all known conductivity sensor types, whether electrode or inductive types. 

If deploying at low temperatures but no surface frazil or pancake ice is present, rinse the conductivity cell in one of the following salty solutions (salty water depresses the freezing point) to prevent freezing during deployment. But this does not mean you can store the cell in one of these solutions outside . . . it will freeze.

  • Solution of 1% Triton in sterile seawater (use 0.5-micron filtered seawater or boiled seawater),   or
  • Brine solution (distilled seawater or homemade salt solution that is higher than 35 psu in salinity).

Note that there is still a risk of forming ice inside the conductivity cell if deploying through frazil or pancake ice on the surface, if the freezing point of the salt water is the same as the water temperature. Therefore, we recommend that you deploy the conductivity cell in a dry state for these deployments.

Commercially available alcohol or glycol antifreezes contain trace amounts of oils that will coat the conductivity cell and the electrodes, causing a calibration shift, and consequently result in errors in the data. Do not use alcohol or glycol in the conductivity cell.

Temperature Sensor

In general, neither the accuracy of the temperature measurement nor the survival of the temperature sensor will be affected by ice.

Oxygen Sensor

For the SBE 43 and SBE 63 Dissolved Oxygen sensor, avoid prolonged exposure to freezing temperature, including during shipment. Do not store the with water (fresh or seawater), Triton solution, alcohol, or glycol in the plenum. The best precaution is to keep the sensor indoors or in some shelter out of the cold weather.

How should I handle my CTD to avoid cracking the conductivity cell?

Shipping: Sea-Bird carefully packs the CTD in foam for shipping. If you are shipping the CTD or conductivity sensor, carefully pack the instrument using the original crate and packing materials, or suitable substitutes.

Use: Cracks at the C-Duct end of the conductivity cell are most often caused by:

  • Hitting the bottom, which can cause the T-C Duct to flex, resulting in cracking at the end of the cell.
  • Removing the soaker tube from the T-C duct in a rough manner, which also causes the T-C Duct to flex. Pulling the soaker tube off at an angle can be especially damaging over time to the cell. Pull the soaker tube off straight down and gently.
  • Improper disassembly of the T-C ducted temperature and conductivity sensors (SBE 25, 25plus, and 9plus) when removing them for shipment to Sea-Bird for calibration. See Shipping SBE 9plus, 25, and 25plus Temperature and Conductivity Sensors for the correct procedure.

Note: If a Tygon tube attached to the conductivity cell has dried out, yellowed, or become difficult to remove, slice (with a razor knife or blade) and peel the tube off of the conductivity cell rather than twisting or pulling the tube off.

Can I brush-clean and replatinize the conductivity cell myself? How often should this be done?

Brush-cleaning and replatinizing should be performed at Sea-Bird. We cannot extend warranty coverage if you perform this work yourself.

The brush-cleaning and replatinizing process requires specialized equipment and chemicals, and the disassembly of the sensor. If performed incorrectly, you can damage the cell. Additionally, the sensor must be re-calibrated when the work is complete.

Sea-Bird determines whether brush-cleaning and replatinizing is required based upon how far the calibration has drifted from the original calibration. Typically, a conductivity sensor on a profiling CTD requires brush-cleaning and replatinizing every 5 years.

Does it matter if I deploy my moored instrument, which includes a conductivity sensor, in a horizontal or vertical position?

Yes, vertical is usually preferable. In the presence of consistent currents and suspended sediment, we have seen instances where a horizontal conductivity cell is scoured by the abrasive effect of the flow. When scouring is particularly intense, the electrodes can be stripped of their electroplated platinum-black coating, driving the calibration toward fresher readings. Sedimentation (silting) in the cell also drives the readings fresh of correct.

Mounting the instrument vertically avoids abrasive flow and sediment build-up while allowing wave motions and Bernoulli pressures to flush the cell.

Note that some moored sensors (SBE 37-SIP37-SIP-IDO, 37-SMP37-SMP-IDO37-SMP-ODO37-IMP37-IMP-IDO37-IMP-ODO) have a recommended orientation because of their u-shaped plumbing configuration. Refer to the instrument manual for details.

What are the typical data processing steps recommended for each instrument?

Section 3: Typical Data Processing Sequences in the SBE Data Processing manual provides typical data processing sequences for our profiling CTDs, moored CTDs, and thermosalinographs. Typical values for aligning, filtering, etc. are provided in the sections detailing each module of the software. This information is also documented in the software's Help file. To download the software and/or manual, go to SBE Data Processing.

Family Model . Housing Pressure Sensor/Range Connectors Communications
19 P . 1 – 600 m (plastic) 1 – 20 m strain gauge 1 – XSG/AG 0 – RS-232
      2 – 7000 m (titanium) 2 – 100 m strain gauge 2 – MCBH  
      3 – 10,500 m (titanium) 3 – 350 m strain gauge    
        4 – 600 m strain gauge    
        5 – 1000 m strain gauge    
        6 – 2000 m strain gauge    
        7 – 3500 m strain gauge    
        8 – 7000 m strain gauge    
        A – 45 psia Digiquartz    
        B – 100 psia Digiquartz    
        C – 200 psia Digiquartz    
        D – 300 psia Digiquartz    
        E – 400 psia Digiquartz    
        F – 1000 psia Digiquartz    
        G – 2000 psia Digiquartz    
        H – 3000 psia Digiquartz    
        I – 6000 psia Digiquartz    
        J – 10,000 psia Digiquartz    
        K – 15,000 psia Digiquartz    

Example: 19P.2820 is an SBE 19plus V2 with 7000 m housing, 7000 m strain gauge pressure sensor, MCBH connectors, and RS-232 communications. See table below for description of each selection:

PART # DESCRIPTION NOTES
19plus V2

SeaCATplus Version 2 Profiler Pumped Conductivity, Temperature, Depth Recorder - 4 Hz sampling rate, includes SNE 5M submersible pump, 64 MB memory, 6 differential A/D channels (0 - 5 volt input range), 1 RS-232 data input channel, data I/O and pump Y-cable, 2.5 meter data I/O cable, Seasoft software, & complete documentation. Configurations that include pumped SBE 43 or other pumped auxiliary sensors require SBE 5T or 5P; see 19p-4_.


19plus V2 in plastic housing with SBE 5M plastic pump & associated plumbing (plumbing configuration shown for 19plus V2 to be deployed in vertical orientation)

19plus V2 is intended primarily as a profiling CTD, sampling at 4 Hz, but can also be used in moored mode to obtain long-term time series data. 19plus V2 is powered by internal batteries, & records data in memory.

In addition, in profiling mode, 19plus V2 can be deployed:

  • With SBE 36 CTD Deck Unit & Power Data Interface Module (PDIM), which provide power & real-time data handling capability over single-conductor sea cables. For PDIM, specify 19p-9a or -9b; order SBE 36 separately.

  • With SBE 32 Carousel Water Sampler & SBE 33 Deck Unit, which provide power, real-time data handling capability, & real-time water sampler control over single-conductor sea cables. Order SBE 32 (32, 32C, or 32SC) & SBE 33 separately.

  • With SBE 32 Carousel Water Sampler & Auto Fire Module (AFM), which provide autonomous water sampling capability. Order SBE 32 (32, 32C, or 32SC) & AFM separately.

 

  • With SBE 55 ECO Water Sampler & SBE 33 Deck Unit, which provide power, real-time data handling capability, & real-time water sampler control over single-conductor sea cables. Order SBE 55 & SBE 33 separately.

  • With SBE 55 ECO Water Sampler, which has built-in capabilities similar to that of an SBE 32 integrated with an AFM, providing autonomous water sampling capability. Order SBE 55 separately.

Notes:

  • Optional auxiliary sensors on CTDs not shown.
  • (real-time systems) Computer, slip-ring-equipped winch, conductive cable, & NMEA 0183 navigation device not supplied by Sea-Bird.
  • (real-time systems) Seasave also supports acquisition of data from a NMEA device connected directly to computer (instead of deck unit).
SBE 19plus V2 Housing (depth) Selections MUST SELECT ONE
19P.1xx0 600 m plastic housing for CTD and SBE 5M plastic pump  
19P.2xx0 7000 m titanium housing for CTD and SBE 5M titanium pump  
19P.3xx0 10,500 m titanium housing for CTD and SBE 5M titanium pump  
SBE 19plus V2 Pressure Sensor Selections MUST SELECT ONE
19P.x1x0 20 m strain gauge pressure sensor Pressure sensor is installed in connector end cap, & is not field replaceable / swappable. While highest pressure rating gives you most flexibility in using 19plus V2, it is at expense of accuracy & resolution. It is advantageous to use lowest range pressure sensor compatible with your intended maximum operating depth, because accuracy & resolution are proportional to pressure sensor's full scale range. For example, comparing 2000 & 7000 m sensors:
  • 2000 m sensor:
    initial accuracy = 2 m (= 0.1% * 2000 m),
    resolution = 0.04 m (= 0.002% * 2000 m)
  • 7000 m sensor:
    initial accuracy = 7 m (= 0.1% * 7000 m),
    resolution = 0.14 m (= 0.002% * 7000 m)
19P.x2x0 100 m strain gauge pressure sensor
19P.x3x0 350 m strain gauge pressure sensor
19P.x4x0 600 m strain gauge pressure sensor
19P.x5x0 1000 m strain gauge pressure sensor
19P.x6x0 2000 m strain gauge pressure sensor
19P.x7x0 3500 m strain gauge pressure sensor
19P.x8x0 7000 m strain gauge pressure sensor
19P.xAx0 45 psia (20 m) Digiquartz pressure sensor with temperature compensation (2 Hz maximum sampling rate) Digiquartz pressure sensors provide better accuracy (0.02% of full scale range vs 0.1% of full scale range) & resolution (Digiquartz resolution dependent on user-programmable integration time) than strain gauge pressure sensors. See strain gauge options above for photo of pressure sensor port; when used with Digiquartz, nylon pressure capillary fitting screws into port.

Pressure sensor is installed in connector end cap, & is not field replaceable / swappable. While highest pressure rating gives you most flexibility in using 19plus V2, it is at expense of accuracy & resolution. It is advantageous to use lowest range pressure sensor compatible with your intended maximum operating depth, because accuracy & resolution are proportional to pressure sensor's full scale range. For example, comparing 2000 psia (1400 m) & 6000 psia (4200 m) sensors:

  • 2000 psia (1400 m) sensor:
    initial accuracy = 0.28 m (= 0.02% * 1400 m)
  • 6000 psia (4200 m) sensor:
    initial accuracy = 0.84 m (= 0.02% * 4200 m)
19P.xBx0 100 psia (60 m) Digiquartz pressure sensor with temperature compensation (2 Hz maximum sampling rate)
19P.xCx0 200 psia (130 m) Digiquartz pressure sensor with temperature compensation (2 Hz maximum sampling rate)
19P.xDx0 300 psia (200 m) Digiquartz pressure sensor with temperature compensation (2 Hz maximum sampling rate)
19P.xEx0 400 psia (270 m) Digiquartz pressure sensor with temperature compensation (2 Hz maximum sampling rate)
19P.xFx0 1000 psia (680 m) Digiquartz pressure sensor with temperature compensation (2 Hz maximum sampling rate)
19P.xGx0 2000 psia (1,400 m) Digiquartz pressure sensor with temperature compensation (2 Hz maximum sampling rate)
19P.xHx0 3000 psia (2,000 m) Digiquartz pressure sensor with temperature compensation (2 Hz maximum sampling rate)
19P.xIx0 6000 psia (4,200 m) Digiquartz pressure sensor with temperature compensation (2 Hz maximum sampling rate)
19P.xJx0 10,000 psia (6,800 m) Digiquartz pressure sensor with temperature compensation (2 Hz maximum sampling rate)
19P.xKx0 15,000 psia (10,500 m) Digiquartz pressure sensor with temperature compensation (2 Hz maximum sampling rate)
SBE 19plus V2 Connector Selections MUST SELECT ONE
19P.xx10 XSG/AG connectors on SeaCAT bulkhead connectors, data I/O and pump Y-cable, and data I/O cable

Wet-pluggable connectors may be mated in wet conditions. Their pins do not need to be dried before mating. By design, water on connector pins is forced out as connector is mated. However, they must not be mated or un-mated while submerged. Wet-pluggable connectors have a non-conducting guide pin to assist pin alignment & require less force to mate, making them easier to mate reliably under dark or cold conditions, compared to XSG/AG connectors. Like XSG/AG connectors, wet-pluggables need proper lubrication & require care during use to avoid trapping water in sockets.

 
These selections include data I/O and pump Y-cable & data I/O cable compatible with data I/O - pump bulkhead connector.

19P.xx20 Wet-pluggable (MCBH) connectors on SeaCAT bulkhead connectors, data I/O and pump Y-cable, and data I/O cable
SBE 19plus V2 Pump Upgrade Options
19p-4a SBE 5P plastic pump, 600 meter, instead of SBE 5M plastic pump (required if using SBE 43 DO sensor) SBE 5M pump is intended for providing pumped conductivity only, for improved conductivity response over non-pumped configuration.

Larger, more powerful SBE 5P or 5T is required if also planning to pump auxiliary sensors (such as dissolved oxygen, etc.).

SBE 5P plastic pump is rated to 600 m; SBE 5T titanium pump is rated to 10,500 m. Operational characteristics of SBE 5P & 5T are identical.

19p-4b SBE 5T titanium pump, 7000 meter, instead of SBE 5M titanium pump (required if using SBE 43 DO sensor)
SBE 19plus V2 Auxiliary Sensor & Integration Options
19p-6a SBE 43 Dissolved Oxygen Sensor (Profiling Configuration), with XSG connector, 7000 m (cable & mount included, requires 19p-4b & 19P.xx10)

General Information:

  • 19p-6, -7, & -8 include auxiliary sensor, mount, & straight cable to connect sensor to 19plus V2 bulkhead connector. See auxiliary sensor specification sheets (SBE 43, 18, 27) for sensor descriptions. Auxiliary sensor connector type (XSG/AG or wet-pluggable) must match 19plus V2 connector type.
  • If connecting 2 sensors to 1 bulkhead connector, YMOLD (to create a y-cable) applies in addition to 19p-6, -7, & -8 price.
  • Additional sensors not listed here — fluorometers, transmissometers, turbidity meters, PAR sensors, etc. from third party manufacturers — are compatible with 19plus V2. These sensors can be purchased from Sea-Bird & integrated with 19plus V2 at our factory, or you can purchase mount kits & cables from Sea-Bird & perform integration yourself. See Third Party portion of price list.
  • User can change sensors on 19plus V2 in field. However, as noted above, Y-cable is required to connect 2 auxiliary sensors to 1 bulkhead connector on 19plus V2; each Y-cable is unique to sensors being integrated, so changing sensors may require changing Y-cable. In addition, sensor mechanical mountings may need to be changed to suit selected combination of sensors.

Sensor-Specific Information:

  • SBE 43 — SBE 43 is available in 7000 m titanium (19p-6a or -6b) or 600 m plastic (19p-6c or -6d) housing. SBE 43 is plumbed between conductivity sensor & pump. Consequently, system requires more powerful SBE 5P plastic (19p-4a) or 5T titanium pump (19p-4b) instead of standard 5M pump; operational characteristics of SBE 5P & 5T are identical.
  • SBE 18 & SBE 27 — Note that these sensors are only available with a depth rating to 1200 m.

Moored Application Information:

  • SBE 43 — If intending to use 19plus V2 in moored application, contact Sea-Bird to specify integration with an SBE 43 in Moored Configuration instead of Profiling Configuration (1 mil membrane vs 0.5 mil membrane for enhanced long-term stability; & black Tygon tubing vs clear Tygon tubing for plumbing, for reduced bio-fouling). Alternatively, we recommend use of the SBE 63 Optical Dissolved Oxygen Sensor for moored applications.
  • SBE 18 & SBE 27 — Sensors are not recommended for use in moored applications. See Application Note 76: pH or pH/ORP Sensors and Moored Applications.
19p-6b SBE 43 Dissolved Oxygen Sensor (Profiling Configuration), with Wet-pluggable connector, 7000 m (cable & mount included, requires 19p-4b & 19P.xx20)
19p-6c SBE 43 Dissolved Oxygen Sensor (Profiling Configuration), with XSG connector, 600 m plastic (cable & mount included, requires 19p-4a or -4b & 19P.xx10)
19p-6d SBE 43 Dissolved Oxygen Sensor (Profiling Configuration) with Wet-pluggable connector, 600 m plastic (cable & mount included, requires 19p-4a or -4b & 19P.xx20)
19p-7a SBE 18 pH sensor, for use in profiling mode only, with XSG connector, 1200 meter (cable and mount included; requires 19P.xx10)
19p-7b SBE 18 pH sensor, for use in profiling mode only, with Wet-pluggable connector, 1200 meter (cable and mount included; requires 19P.xx20)
19p-8a SBE 27 pH/ORP sensor, for use in profiling mode only, with AG connector, 1200 meter (cable and mount included; requires 19P.xx10)
19p-8b SBE 27 pH/ORP sensor, for use in profiling mode only, with Wet-pluggable connector, 1200 meter (cable and mount included; requires 19P.xx20)
YMOLD Extra charge for Y-cable to connect two (2) or more sensors to one (1) auxiliary sensor input bulkhead connector on CTD
19p-9a Underwater power/data interface module (PDIM) with XSG connectors, integrated for use with SBE 36 CTD Deck Unit or 33 Carousel Deck Unit (includes PDIM, interface cable, and mounting hardware; requires 19P.xx10)

SBE 36 CTD Deck Unit & PDIM provide surface power & real-time data acquisition & control for 19plus V2, allowing deployment with 10,000 m long single-conductor sea cables. SBE 36 is installed on ship, while PDIM is mounted on or near 19plus V2. See SBE 36 description for more information on interface.

SBE 33 Deck Unit is typically used to provide surface power & real-time data acquisition & control for 19plus V2 & SBE 32 (32, 32C, or 32SC) Carousel Water Sampler or SBE 55 ECO Water Sampler. However, it can be used with PDIM instead of Carousel or ECO to provide same functionality as SBE 36 & PDIM.

PDIM housing is anodized aluminum, & is rated to 6800 m. PDIM connector type (XSG or wet-pluggable) must match 19plus V2 connector type.

19p-9a & -9b do not include SBE 36 or 33 Deck Unit; order separately.

 
Can substitute SBE 33 Carousel Deck Unit for SBE 36 CTD Deck Unit.

19p-9b Underwater power/data interface module (PDIM) with Wet-pluggable connectors, integrated for use with SBE 36 CTD Deck Unit or 33 Carousel Deck Unit (includes PDIM, interface cable, and mounting hardware; requires 19P.xx20)
SBE 19plus V2  Hardigg Shipping Case option
19p-10 Hardigg shipping case (AL4915-1105) instead of wood crate, for SBE 19plus V2 in optional cage

Hardigg shipping case with custom foam inserts holds SBE 19plus V2 with auxiliary sensors in optional cage (SBE 9plus shown; SBE 19plus V2 similar).

  • Rotationally molded high-impact polyethylene with reinforced corners & edges, molded-in corrugations, reinforced corners & edges, tongue-in-groove seal, positive anti-shear locks, comfort-grip handle, recessed hardware. Meets airline luggage regulations.
  • Inner dimensions:
    49 x 14.8 x 16.2 inches (124 x 38 x 41 cm).
  • Outer dimensions:
    52 x 17.8 x 18.4 inches (132 x 45 x 47 cm).

Note: 19plus V2 with Digiquartz pressure sensor requires a longer cage (PN 801270) than 19plus V2 with strain-gauge pressure sensor. PN 801270 cage does not fit in this Hardigg shipping case; contact Sea-Bird to discuss purchasing a larger case.

Price for 19p-10 reflects a credit for deletion of our standard wood crate.

Notes regarding features of Hardigg case supplied by Sea-Bird:
1. Case does not have wheels, because we prefer that the case is not rolled along the ground:
- Rolling along the ground could cause unnecessary vibration of the CTD.
- Rolling over a curb could cause unnecessary impact to the CTD.
2. Case has small holes on each metal latch, into which you could insert a small, TSA-approved lock or some zip ties. Case cannot accommodate a large padlock.

SBE 19plus V2 Spares & Accessories
801269 Stainless-steel protective cage, 40 in. (101 cm) tall (SeaCATplus) Many users purchase optional cage to protect system from damage during deployment.
  • 801269 (drawing 22009) — cage for 19plus V2 with strain-gauge pressure sensor
  • 801270 (drawing 22010) — cage for 19plus V2 with Digiquartz pressure sensor (Digiquartz sensor requires longer 19plus V2 housing, which requires a taller cage)
  • 50396 (drawing 20893) — cage for 19plus V2 with strain gauge pressure sensor, mounted horizontally in extension stand below SBE 32 (full size) Carousel Water Sampler (requires shorter cage).
    Note: For 19plus V2 with Quartz pressure sensor, contact Sea-Bird.

See document 67171 for installation details.

Notes:

  • 801269 and 801270 are for use with SBE 19plus or 19plus V2, but not with older SeaCAT (SBE 19).
  • 19plus V2 deployed on SBE 32C (compact) or 32SC (subcompact) Carousel Water Sampler is mounted in bottle position on Carousel, & does not use cage.
  • 19plus V2 deployed on SBE 55 ECO Water Sampler is mounted on mesh panel, & does not use cage.
  • For cage with small footprint, typically used for deployment through ice, see drawing 22149 and photo on Gallery tab.
801270 Stainless-steel protective cage, 48 in. (123 cm) tall (SeaCATplus with Digiquartz)
50396 Stainless-steel protective cage, 38 in. (96 cm) tall, used in SBE 32 Carousel CTD extension stand
50434 SBE 16plusV2/19plusV2 Spares Kit (XSG/AG connectors) - Complete support kit containing spare data I/O cable, bulkhead connectors, dummy plugs, Triton X-100, o-ring lubricant, & other mechanical spares & maintenance items. Order appropriate spares kit for connector type on 19plus V2:
  • 50434 for 19plus V2 with XSG/AG connectors — See document 67196.
  • 50435 for 19plus V2 with wet-pluggable connectors — See document 67197.
50435 SBE 16plusV2/19plusV2 Spares Kit (Wet-pluggable connectors) - Complete support kit containing spare data I/O cable, bulkhead connectors, dummy plugs, Triton X-100, o-ring lubricant, & other mechanical spares & maintenance items.
801511 9 NiMH cells in rechargeable drop-in pack (108v/8.0 Ah)

19plus V2 comes standard with alkaline batteries, but can be powered with rechargeable NiMH batteries instead. Batteries are easily accessed by unscrewing battery end cap.

      
90504 NiMH Battery Charger for 6, 9, or 12-cell/8.0 Ah D-cell packs. Provides full recharge in 2 hours, includes AC power cord and battery charging cable.
50288

SBE 19plus/19plusV2 Moored Mode Conversion Kit - anti-foulant holders and hardware for user conversion from profiling to moored mode configuration. AF24173 anti-foulant devices (PN 801542) are NOT included. Note: When installed on 19plus/19plusV2 at time of order, the T-C Duct and related parts normally installed on profilers are provided as a separate Profiling Conversion Kit, PN 50345 (order 801542 anti-foulant devices separately, or PN 50288.1 Kit with anti-foulant devices)

19plus V2 is intended primarily for use as profiling instrument, & does not come standard with anti-foulant device fittings. Conversion kit allows user to retrofit 19plus V2 with anti-foulant device fittings for moored applications. Anti-foulant device fittings attach to each end of conductivity cell. See document 67114. Only 1 conversion kit is needed per instrument; order replacement Anti-Foulant Devices as needed (see next item).
801542 AF24173 Anti-Foulant Device pair (spare, bagged, labeled for shipping) Anti-foulant devices fit into anti-foulant device cups at each end of conductivity cell. Anti-foulant devices included with standard shipment; these are spares.
Useful life varies, depending on several factors. We recommend that customers consider more frequent replacement when high biological activity & strong current flow (greater dilution of anti-foulant concentration) are present. Moored instruments in high growth & strong dilution environments have been known to obtain a few months of quality data, while drifters that operate in non-photic, less turbid deep ocean environments may achieve years of quality data. Experience may be strongest determining factor in specific deployment environments.
20200 USB to Serial Port Adapter, FTDI UC232R-10 (connects computers with USB ports to RS-232 instruments) Many newer PCs & laptop computers have USB port(s) instead of RS-232 serial port(s). USB serial adapter plugs into USB port, & allows a serial device to be connected through adapter. Multi-port adapters are available from other companies; see Application Note 68.
31634 Hardigg shipping case (AL4915-1105), for SBE 19plus/19plus V2 in optional cage Hardigg shipping case with custom foam inserts holds SBE 19plus V2 with auxiliary sensors in optional cage (SBE 9plus shown; SBE 19plus V2 similar).
  • Rotationally molded high-impact polyethylene with reinforced corners & edges, molded-in corrugations, reinforced corners & edges, tongue-in-groove seal, positive anti-shear locks, comfort-grip handle, recessed hardware. Meets airline luggage regulations.
  • Inner dimensions:
    49 x 14.8 x 16.2 inches (124 x 38 x 41 cm).
  • Outer dimensions:
    52 x 17.8 x 18.4 inches (132 x 45 x 47 cm).

Note: 19plus V2 with Digiquartz pressure sensor requires a longer cage (PN 801270) than 19plus V2 with strain-gauge pressure sensor. PN 801270 cage does not fit in this Hardigg shipping case; contact Sea-Bird to discuss purchasing a larger case.

Notes regarding features of Hardigg case supplied by Sea-Bird:
1. Case does not have wheels, because we prefer that the case is not rolled along the ground:
- Rolling along the ground could cause unnecessary vibration of the CTD.
- Rolling over a curb could cause unnecessary impact to the CTD.
2. Case has small holes on each metal latch, into which you could insert a small, TSA-approved lock or some zip ties. Case cannot accommodate a large padlock.

50275 SBE 19plus/19plus V2 magnetic switch assembly Replacement for magnetic switch, which is used to start & stop logging. See document 67101.
41124 Battery cover/contact plate, replaces 80076.1 Cover plate for alkaline batteries.
801225 Data I/O cable, RMG-4FS with DB-9S, 2.4 m (DN 32421)

These test cables are used for setting up system & uploading data from memory after recovery. Data I/O cable connects to 4-pin end of pump-data I/O Y-cable.

Connector type (RMG or wet-pluggable) must match 19plus V2 connector type. Applicable cable is included with 19plus V2; these are spares.

801374 Data I/O cable, Wet-pluggable (MCIL-4FS) with DB-9S, 2.4 m (DN 32715)
17709 Y-cable, Pump-Data I/O, XSG/AG connectors (DN 31551) These Y-cables connect 6-pin data I/O - pump bulkhead connector to pump (2-pin leg) & to data I/O cable (4-pin leg).
171883 Y-cable, Pump-Data I/O, Wet-pluggable connectors (DN 32896)
90087 Universal plumbing kit (includes pump air release valve, Y-fitting, & tubing) - Application Note 64-1 Application Note 64-1 details installation of plumbing for SBE 43 & pump on a CTD.
50087 Cell filler/storage device with hose barbs (Application Note 34) For cleaning conductivity cell after each use & storing instrument between uses. See document 67043 & Application Note 2D: Instructions for Care and Cleaning of Conductivity Cells.
various Plumbing For assorted sizes of Tygon tubing, see SBE 5M or 5P or 5T Configuration.
Underwater Cable for Hand-Hauled, Real-Time Profiling (see Application Note 59 for proper use and limitations)
801150 Load-bearing Data cable, XSG connector with DB-9S, 100 feet (30 m) (DN 32284)

These cables are for hand-hauling 19plus V2 & acquiring real-time data. Cables are not intended for static working loads above 45 kg (100 lbs); working loads above 18 kg (40 lbs) may be difficult to handle without winch. Minimum recommended cable bend radius is 10 cm (4 in.) (e.g., 20 cm sheave block nominal diameter). See Application Note 59: A Load-Bearing Underwater Cable for Hand-Hauled, Real-Time Profiling.

Select a cable with connector (XSG or wet-pluggable MCBH) to match your 19plus V2.

801295 Load-bearing Data cable, XSG connector with DB-9S, 165 feet (50 m) (DN 32284)
801140 Load-bearing Data cable, XSG connector with DB-9S, 200 feet (61 m) (DN 32284)
801153 Load-bearing Data cable, XSG connector with DB-9S, 330 feet (100 m) (DN 32284)
801301 Load-bearing Data cable, XSG connector with DB-9S, 415 feet (126 m) (DN 32284)
801148 Load-bearing Data cable, XSG connector with DB-9S, 600 feet (183 m) (DN 32284)
801371 Load-bearing Data cable, Wet-pluggable with DB-9S, 100 feet (30 m) (DN 32643)
801372 Load-bearing Data cable, Wet-pluggable with DB-9S, 200 feet (60 m) (DN 32643)
801337 Load-bearing Data cable, Wet-pluggable with DB-9S, 330 feet (100 m) (DN 32643)
801338 Load-bearing Data cable, Wet-pluggable with DB-9S, 660 feet (200 m) (DN 32643)

 

Cables

  • 801225 To computer COM port (from XSG connector), 2.4 m, DN 32421
    Note: 801225 connects to 4-pin end of Y-cable 17709.
  • 801374 To computer COM port (from Wet-pluggable connector), 2.4 m, DN 32715
    Note: 801374 connects to 4-pin end of Y-cable 171883.
  • Part # varies with length, To computer COM port, load-bearing cable (from XSG connector), DN 32284 (also see Application Note 59)
    Note: Load-bearing cable connects to 4-pin end of Y-cable 17709.
  • Part # varies with length, To computer COM port, load-bearing cable (from Wet-pluggable connector), DN 32643 (also see Application Note 59)
    Note: Load-bearing cable connects to 4-pin end of Y-cable 171883.
  • 17709 To SBE 5M, 5T, or 5P (Y-cable to pump and data I/O, RMG/AG connectors), DN 31551
  • 171883 To SBE 5M, 5T, or 5P (Y-cable to pump and data I/O, Wet-pluggable connectors), DN 32896
  • 17595 To SBE 18 (RMG/AG connectors), 1.1 m, DN 30918
  • 171704 To SBE 27 (AG connectors), 1.1 m, DN 31749
  • 17292 To SBE 32 (RMG connectors), 2 m, DN 30567
  • 171912 To SBE 32 (Wet-pluggable connectors), 2 m, DN 32810
  • 172447 To SBE 43 (RMG/AG connectors), 1.1 m, DN 32496
  • 172448 To SBE 43 (Wet-pluggable connectors), 1.1 m, DN 32654
  • 172259 To SBE 55 (RMG/AG connectors), 1.2 m, DN 33191
  • 172260 To SBE 55 (Wet-pluggable connectors), 1.2 m, DN 33192
  • 17088 To SBE 63 (RMG connectors), 1.1 m, DN 30567
  • 171792 To SBE 63 (Wet-pluggable connectors), 1.1 m, DN 32810
  • 17821 To Auto Fire Module (AFM) (RMG connectors), 1.2 m, DN 31670
  • 17884 To Auto Fire Module (AFM) (RMG connectors), 1.8 m, DN 31670
  • 171846 To Auto Fire Module (AFM) (Wet-pluggable connectors), 1.8 m, DN 32859
  • 17088 To Power & Data Interface Module (PDIM), (RMG connectors), 1.1 m, DN 30567
  • 171792 To Power & Data Interface Module (PDIM), (Wet-pluggable connectors), 1.1 m, DN 32810
  • 171130 To Benthos/Datasonics PSA-916 (from AG connector), 1.8 m, DN 32075
  • 17610 To Biospherical QSP-200L or QSP-2300L (from AG connector), 2 m, DN 30701
  • 17602 To Chelsea AquaTracka or AlphaTracka (from AG connector), 1.2 m, DN 31253
  • 17361 To D&A OBS-3 (from AG connector), 0.76 m, DN 30954
  • 172130 To D&A OBS-3+ (from AG connector), High & Low range, 1 m, DN 33080
  • 172131 To D&A OBS-3+ (from Wet-pluggable connector), High & Low range, 1 m, DN 33081
  • 172109 To D&A OBS-3+ (from AG connector), Low range (1X), 1 m, DN 33058
  • 172111 To D&A OBS-3+ (from Wet-pluggable connector), Low range (1X), 1 m, DN 33060
  • 172110 To D&A OBS-3+ (from AG connector), High range (4X), 1 m, DN 33059
  • 172112 To D&A OBS-3+ (from Wet-pluggable connector), High range (4X), 1 m, DN 33061
  • 172215 To Satlantic SatPAR (from AG connector), 2 m, DN 32628
  • 172214 To Satlantic SatPAR (from Wet-pluggable connector), 2 m, DN 32654
  • 171099 To Seapoint fluorometer or turbidity meter (1X) (from V2 AG connector), 1.1 m, DN 32073
  • 171147 To Seapoint fluorometer or turbidity meter (3X/5X) (from AG connector), 1.1 m, DN 32101
  • 172221 To Seapoint fluorometer or turbidity meter (10X/20X) (from AG connector), 1.1 m, DN 31933
  • 171845 To Seapoint fluorometer or turbidity meter (30X/100X) (from AG connector), 1.1 m, DN 31924
  • 171908 To Turner Cyclops-7 (1X) (from AG connector), 1.1 m, DN 32910
  • 171907 To Turner Cyclops-7 (10X) (from AG connector), 1.1 m), DN 32909
  • 171909 To Turner Cyclops-7 (100X) (from AG connector), 1.1 m, DN 32911
  • 171418 To Turner SCUFA (from AG connector), 1.1 m, DN 32417
  • 17876 To WET Labs C-Star or WETStar with old-style 4-pin connector (from AG connector), 1.1 m, DN 31725
  • 171953 To WET Labs ECO-AFL, ECO-FL, C-Star, or WETStar with new-style 6-pin connector (from AG connector), 1.1 m, DN 32491
  • 172437 To WET Labs ECO-AFL, ECO-FL, C-Star, or WETStar with new-style 6-pin connector (from Wet-pluggable connector), 1.1 m, DN 32853
  • 171869 To WET Labs ECO-FL-NTUS or ECO-FL-NTU(RT) (from AG connector), 1.1 m, DN 32812
  • 172285 To WET Labs ECO-FL-NTUS or ECO-FL-NTU(RT) (from Wet-pluggable connector), 1.1 m, DN 32846
  • 172880 To WET Labs Triplet or Triplet-W (from AG connector), 1.1 m, DN 33673
  • 172815 To WET Labs Triplet or Triplet-W (from Wet-pluggable connector), 1.1 m, DN 33622
  • 17015 To AC power supply from NiMH Battery Charger (U.S. Standard)
  • 801509 To NiMH battery pack (from NiMH Battery Charger), DN 32935

Mount Kits

SeaCATplus Cage

  • 801269 SBE 16plus/16plus V2/19plus/19plus V2 to PN 801269 Cage (document 67171 and drawing 22009)
  • 801270 SBE 16plus/16plus V2/19plus/19plus V2 to PN 801270 Tall Cage; required for SBE 16plus/16plus V2/19plus/19plus V2 with Quartz pressure sensor (document 67171 and drawing 22010)

Note: These cages do not fit inside SBE 32 Carousel extension stand, for mounting horizontally below Carousel. If mounting a 19plus V2 (with strain gauge pressure sensor) in extension stand, order PN 50396 instead (drawing 20893); contact Sea-Bird for a 19plus V2 with Quartz pressure sensor.

To SBE 32

  • 50121 SeaCAT/Sealogger/AFM to SBE 32 Bottle Position Mount Kit (document 67020)
  • 50124 SBE 32 Cage Mount Kit — Ring Top; required to mount older CTD cage with ring top in CTD extension stand below full size SBE 32 Carousel (document 67186)

To SBE 55

  • 50422 SBE 55 Universal CTD / Electronics Installation Kit (document 67179)

Spare Parts

Batteries

  • 801511 9 NiMH cells in rechargeable drop-in pack (10.8V/8 Ah)
  • 90504 NiMH battery charger for 6, 9, or 12 cells / 8 Ah D-cell packs. Provides full recharge in 2 hours, includes AC power cord & battery charging cable
  • 801641 9 Ni-Cad cells in drop-in rechargeable pack (10.8V/4.4 Ah)

Note: As of 2011, Sea-Bird does not manufacture the 90226 Ni-Cad battery charger, because parts are no longer available. We are still able to provide the battery pack, for customers who already have a charger.

Hardware & O-ring Kits

  • 41124 Battery cover/contact plate, replaces 80076.1
  • 60021 Battery end cap hardware & O-ring kit for SBE 16/16plus/16plus-IM/16plus V2/16plus-IM V2, 17plus, 19/19plus/19plus V2, 25, 26/26plus, 53, 54, 55, or AFM (document 67042)
  • 50274 O-ring kit for SBE 16plus, 16plus-IM, 16plus V2, 16plus-IM V2, 19plus, or 19plus V2 (document 67102)
  • 50273 Hardware kit for SBE 16plus, 16plus-IM, 16plus V2, 16plus-IM V2, 19plus, or 19plus V2 (document 67103)
  • 50275 Magnetic switch kit for SBE 19plus or 19plus V2 (document 67101)
  • 90087 CTD plumbing kit (document 67108)
  • 50434 Seaspares kit for SBE 16plus V2 or 19plus V2 with XSG/AG connectors (hardware, O-rings, magnetic switch, cable, dummy plugs, connectors, etc.) (document 67196)
  • 50435 Seaspares kit for SBE 16plus V2 or 19plus V2 with wet-pluggable connectors (hardware, O-rings, magnetic switch, cable, dummy plugs, connectors, etc.) (document 67197)

Cages

  • 801269 & Stainless-steel protective cage, 40 inch (101 cm) tall (drawing 22009 and document 67171) — for 19plus or 19plus V2 with strain-gauge pressure sensor
  • 801270 * Stainless-steel protective cage, 48 inch (123 cm) tall (drawing 22010 and document 67171) — for 19plus V2 with Digiquartz pressure sensor
  • 232012 Stainless-steel protective cage with small footprint, for deploying through ice (drawing 22149 and photo on Gallery tab)

* Note: PN 801269 and 801270 cages do not fit inside SBE 32 Carousel extension stand, for mounting horizontally below Carousel. If mounting a 19plus or 19plus V2 (with strain gauge pressure sensor) in extension stand, use PN 23892 cage instead (drawing 20893); contact Sea-Bird for a 19plus V2 with Quartz pressure sensor.

Miscellaneous

  • 801542 AF24173 Anti-Foulant Device (pair, bagged, labeled for shipping)
  • 50288 Moored mode conversion kit for SBE 19plus or 19plus V2 (document 67114)
  • 233186 High-head pressure port plug for muddy/biologically productive environments (for instrument with Druck pressure sensor, moored application) (Application Note 84)
  • 31634 Hardigg shipping case (AL4915-1105), for SBE 19plus or 19plus V2 in cage (photo of 9plus in this shipping case)
    Note: 19plus V2 with Digiquartz pressure sensor requires a longer cage (PN 801270) than 19plus V2 with strain-gauge pressure sensor. PN 801270 cage does not fit in this Hardigg shipping case; contact Sea-Bird to discuss purchasing a larger case.

 

Compare Profiling CTDs (Conductivity, Temperature, and Pressure)

SBE Sampling Rate Channels for Auxiliary Sensors Memory Power Real-Time Data Comments
Internal External
SBE 911plus CTD (9plus CTD & 11plus Deck Unit) 24 Hz

8 A/D

16 Mb with optional SBE 17plus V2
(with optional SBE 17plus V2)
World's most accurate, high resolution CTD, premium sensors, multi-parameter support, water sampler control.
SBE 25plus Sealogger CTD 16 Hz 8 A/D;
2 RS-232
2 Gb
May require SBE 36 CTD Deck Unit & PDIM
High-resolution logging CTD with multi-parameter support. Water sampler control with SBE 33 Carousel Deck Unit.
SBE 25 Sealogger CTD
8 Hz 7 A/D 8 Mb
May require SBE 36 CTD Deck Unit & PDIM
Replaced by SBE 25plus in 2012. Water sampler control with SBE 33 Carousel Deck Unit.
SBE 19plus V2 SeaCAT Profiler CTD 4 Hz 6 A/D;
1 RS-232
64 Mb
May require SBE 36 CTD Deck Unit & PDIM
Personal CTD, small, self-contained, adequate resolution. Water sampler control with SBE 33 Carousel Deck Unit.
SBE 19plus SeaCAT Profiler CTD
4 Hz 4 A/D; optional PAR 8 Mb
May require SBE 36 CTD Deck Unit & PDIM
Replaced by SBE 19plus V2 in 2008. Water sampler control with SBE 33 Carousel Deck Unit.
SBE 19 SeaCAT Profiler CTD
2 Hz 4 A/D 1 - 8 Mb
May require SBE 36 CTD Deck Unit & PDIM
Replaced by SBE 19plus in 2001. Water sampler control with SBE 33 Carousel Deck Unit.
SBE 49 FastCAT CTD Sensor 16 Hz      
May require SBE 36 CTD Deck Unit & PDIM
For towed vehicle, ROV, AUV, or other autonomous profiling applications. Water sampler control with SBE 33 Carousel Deck Unit.
SBE 52-MP Moored Profiler CTD & (optional) Dissolved Oxygen Sensor 1 Hz 1 frequency channel for dissolved oxygen sensor 28,000 samples   Intended for moored profiling applications on device that is winched up and down from a buoy or bottom-mounted platform.
SBE 41/41CP CTD Module for Autonomous Profiling Floats (Argo) OEM CTD for sub-surface oceanographic float that surfaces at regular intervals, transmits new drift position and in situ measurements to ARGOS satellite system. CTD obtains latest temperature and salinity profile for transmission on each ascent. Also available is a Navis Autonomous Profiling Float, Navis BGC Autonomous Profiling Float with Biogeochemical Sensors, and Navis BGCi Autonomous Profiling Float with Integrated Biogeochemical Sensors
Glider Payload CTD (GPCTD) and Slocum Glider Payload CTD OEM CTD for autonomous gliders. Generic Glider Payload CTD (GPCTD) is modular, low-power profiling instrument that measures C, T, P, and (optional) Dissolved Oxygen. Slocum Glider Payload CTD provides retrofit/replacement for CTDs on Slocum gliders. Designs share many features, but there are differences in packaging, sampling abilities, power consumption, and installation (see individual data sheets).
Notes:
1. See Application Note 82: Guide to Specifying a CTD.
2. products are no longer in production. Follow the links above to the product page to retrieve manuals and application notes for these older products.

Compare  Moored / Time Series Recording Instruments

SBE Measures
(C, T, P)
Auxiliary Sensors Memory Power Communication Real-Time
Data
Comments
Internal External
SBE 16plus V2 SeaCAT C-T (P) Recorder C, T, P* 6 A/D; 1 RS-232 64 Mb RS-232 Optional pump
SBE 16plus SeaCAT C-T (P) Recorder
C, T, P* 4 A/D; optional RS-232 or PAR 8 Mb RS-232 or -485 Replaced by SBE 16plus V2 in 2008
SBE 16 SeaCAT C-T (P) Recorder
C, T, P* 4 A/D 1 Mb RS-232 Replaced by 16plus in 2001
SBE 16plus-IM V2 SeaCAT C-T (P) Recorder C, T, P* 6 A/D; 1 RS-232 64 Mb   Inductive Modem Optional pump
SBE 16plus-IM SeaCAT C-T (P) Recorder
C, T, P* 4 A/D; optional RS-232 or PAR 8 Mb   Inductive Modem Replaced by SBE 16plus-IM V2 in 2008
SBE 19plus V2 SeaCAT Profiler CTD C, T, P 6 A/D; 
1 RS-232
64 Mb RS-232 Programmable mode — profiling or moored
SBE 19plus SeaCAT Profiler CTD
C, T, P 4 A/D; optional PAR 8 Mb RS-232 Replaced by SBE 19plus V2 in 2008
SBE 19 SeaCAT Profiler CTD
C, T, P 4 A/D 1 - 8 Mb RS-232 Replaced by 19plus in 2001
SBE 37-SM MicroCAT C-T (P) Recorder C, T, P*   8 Mb RS-232 or -485  
SBE 37-SMP MicroCAT C-T (P) Recorder C, T, P*   8 Mb RS-232, RS-485, or SDI-12 Integral pump

SBE 37-SMP-IDO MicroCAT C-T-DO (P) Recorder

C, T, P* Integrated DO 8 Mb RS-232 or -485 Integral pump
SBE 37-SMP-ODO MicroCAT C-T-DO (P) Recorder C, T, P* Integrated Optical DO 8 Mb RS-232, RS-485, or SDI-12 Integral pump
SBE 37-IM MicroCAT C-T (P) Recorder C, T, P*   8 Mb   Inductive modem  
SBE 37-IMP MicroCAT C-T (P) Recorder C, T, P*   8 Mb   Inductive modem Integral pump
SBE 37-IMP-IDO MicroCAT C-T-DO (P) Recorder C, T, P* Integrated DO 8 Mb   Inductive modem Integral pump
SBE 37-IMP-ODO MicroCAT C-T-DO (P) Recorder C, T, P* Integrated Optical DO 8 Mb   Inductive modem Integral pump
SBE 37-SI MicroCAT C-T (P) Recorder C, T, P*   8 Mb   RS-232 or -485  
SBE 37-SIP MicroCAT C-T (P) Recorder C, T, P*   8 Mb   RS-232 or -485 Integral pump

SBE 37-SIP-IDO MicroCAT C-T-DO (P) Sensor

C, T, P* Integrated DO 8 Mb   RS-232 or -485 Integral pump
Water Quality Monitor (WQM) C, T, P Integrated DO, chlorophyll fluorescence, turbidity (WQMx adds CDOM fluorescence, replaces turbidity with backscattering)   RS-232 Jointly developed by Sea-Bird Electronics and WET Labs; manufactured by WET Labs
SBE 39plus Temperature (P) Recorder T, P*   64 Mb Optional USB & RS-232 Optional  
SBE 39 Temperature (P) Recorder
T, P*   32 Mb Optional RS-232 Optional Replaced by SBE 39plus in 2014
SBE 39-IM Temperature (P) Recorder T, P*   32 Mb   Inductive modem  
SBE 56 Temperature Logger T   64 Mb   USB    
SBE 26plus Seagauge Wave & Tide Recorder T, P C optional 32 Mb RS-232
(tides, waves, & wave statistics)
Wave & tide recorder
SBE 26 Seagauge Wave & Tide Recorder
T, P C optional 8 Mb RS-232   Replaced by SBE 26plus in 2004
SBE 53 BPR Bottom Pressure Recorder T, P C optional 32 Mb RS-232 Bottom pressure recorder
SBE 54 Tsunameter Tsunami Pressure Sensor T, P   128 Mb Optional RS-232 Tsunami pressure sensor

C = conductivity, T = temperature, P = pressure, DO = dissolved oxygen
* = optional
products are no longer in production. Follow the links above to the product page to retrieve manuals and application notes for these older products.